US-30 / 40 CUTTING
MACHINE
Static or Conveyorized Tables
| Machine Configurations and Options | US-30 | US-40 |
| Static cutting table | X | X |
| Static cutting table for Pendular Operation | X | X |
| Conveyorized cutting table | X | X |
| Conveyorized cutting and unloading table for single nesting cutting | X | X |
| Conveyorized cutting and unloading table for continuous nest cut. | X | X |
| Separate conveyorized loading/unloading table to conveyorized machine | X | X |
| Zoned cutting table | X | X |
| Dispensing stand | X | X |
| Single roll dispenser | X | X |
| Four roll dispenser with additional position for vacuum membrane | X | X |
| Cover sheet dispensing stand | X | X |
| Single layer material handling system for: | ||
| Static cutting table | X | X |
| Static cutting table for Pendulum Operation | X | X |
| Conveyorized cutting table | X | X |
| Conveyorized cutting and unloading table | X | X |
| Multi-layer material handling system for: | ||
| Static cutting table | X | X |
| Static cutting table for Pendulum Operation | X | X |
| Conveyorized cutting table | X | X |
| Conveyorized cutting and unloading table | X | X |
| Cones for unwind position | X | X |
| Thermal Transfer printer | X | X |
| INKJET - Printing in one direction | - | - |
| INKJET - Printing in two perpendicular directions | - | - |
| INKJET - Infinitely printing in +/- 90degrees | - | - |
| Nesting System (Software - PC-Version) | NS2/NS2-PC | NS2/NS2-PC |
| Pre-Post-Processor Software ( PC-Version ) | AGFM | AGFM |
| Digitizing System | X | X |
| Network to Host System | X | X |
| Remote Support Option | X | X |
| Electrical Power Supply | ||
| Power Supply - Voltage 50/60Hz | 480V or 600V | 480V or 600V |
| Power Supply - Consumption Machine | 13kVA | 20kVA |
| Power Supply - Consumption Vacuum |
29kVA up to 5m 58kVA up to 10m |
29kVA up to 5m 58kVA up to 10m |
| Compressed Air Supply | ||
| Air Supply Pressure | min.6bar abs | min.6bar abs |
| Air Supply Volume | approx. 10Nm3/hr | approx. 10Nm3/hr |
| Cutting Technology | ||
| Ultrasonic generator | GFM | GFM |
| Output power | max. 800 Watt | max. 800 Watt |
| Frequency | 20000Hz | 20000Hz |
| Noise Level | ||
| Machine without vacuum aggregate | max.82 dB(A) | max.82 dB(A) |
| Vacuum Option | ||
| - 29kVA aggregate | max. 82 dB(A) | max. 82 dB(A) |
| - 58kVA aggregate | max.87 dB(A) | max.87 dB(A) |
| Machine Dimensions | ||
| Cutting area | per spec.. | per spec.. |
| X-axis stroke | per spec.. | per spec.. |
| Y-axis stroke | 1800mm | approx.1800mm |
| Z-axis stroke | 70mm | 80mm |
| C-axis stroke | n*360 deg. | n*360 deg. |
| Cutting Speeds | ||
| Maximum Cutting speed (X,Y) | 0-60m/min | 0-60m/min |
| Acceleration/deceleration (X,Y) Rapid move / Cutting | 2.5m/s² / 2.5m/s² | 2.5m/s² / 2.5m/s² |
| Acceleration/deceleration (Z) | max. 2.5m/s2 | max. 2.5m/s2 |
| Acceleration/deceleration (C) | 900 rad/s2 | 900 rad/s2 |
| Dynamic Acceleration Factor | ||
| Machine Accuracy | ||
| Positioning accuracy in X + Y | ±0.075mm | ±0.075mm |
| Repeatability in X + Y | ±0.03mm | ±0.03mm |
| Profiling Accuracy | ±0.2mm | ±0.125mm |
| Drive System | ||
| Motors | AC-Servo Motors | AC-Servo Motors |
| Control System | ||
| Type | AGFM CNC6000 | AGFM CNC6000 |