|
Machine
Configurations and Options |
US-15 |
US-20 |
|
Static cutting table |
X |
X |
|
Static cutting table for
Pendular Operation |
X |
X |
|
Conveyorized cutting
table |
X |
X |
|
Conveyorized cutting and
unloading table for single nesting cutting |
X |
X |
|
Conveyorized cutting and
unloading table for continuous nest cut. |
X |
X |
|
Separate conveyorized
loading/unloading table to conveyorized machine |
X |
X |
|
Zoned cutting table |
X |
X |
|
Dispensing stand |
X |
X |
|
Single roll dispenser |
X |
X |
|
Four roll dispenser with
additional position for vacuum membrane |
X |
X |
|
Cover sheet dispensing
stand |
X |
X |
|
Single layer material
handling system for: |
|
|
|
- static cutting table |
X |
X |
|
- static cutting
table for Pendulum Operation (loading from one side) |
X |
X |
|
- conveyorized
cutting table |
X |
X |
|
- conveyorized
cutting and unloading table for single nest cutting |
X |
X |
|
Multi-layer material
handling system for: |
|
|
|
- static cutting
table |
X |
X |
|
- static cutting
table for Pendular Operation (loading from one side) |
X |
X |
|
- conveyorized
cutting table |
X |
X |
|
- conveyorized
cutting and unloading table for single nest cutting |
X |
X |
|
Cones for unwind
position |
X |
X |
|
Thermotransfer printer
(not carried by machine) |
X |
X |
|
INKJET - Print in one
direction |
- |
- |
|
INKJET - Print in two
perpendiculardirections |
- |
- |
|
INKJET - Infinitely
printing in +/- 90degrees |
- |
- |
|
Nesting System (Software
- PC-Version) |
NS2/NS2-PC |
NS2/NS2-PC |
|
- Pre-Post-Processor
Software ( PC-Version ) |
PP |
PP |
|
Digitizing System |
X |
X |
|
Network to Host System |
X |
X |
|
Remote Support Option |
X |
X |
|
Electrical Power Supply |
|
|
|
Power Supply - Voltage
50/60Hz |
480V or 600V |
480V or 600V |
|
Power Supply -
Consumption Machine |
10kVA |
10kVA |
|
Power Supply -
Consumption Vacuum |
29kVA up to 5m
58kVA up to 10m |
29kVA up to 5m
58kVA up to 10m |
|
Compressed Air Supply |
|
|
|
Air Supply Pressure |
min.6bar abs |
min.6bar abs |
|
Air Supply Volume |
approx. 10Nm3/hr |
approx. 10Nm3/hr |
|
Cutting
Technology |
|
|
|
Ultrasonic generator |
GFM |
GFM |
|
Output power |
max. 800 Watt |
max. 800 Watt |
|
Frequency |
20000Hz |
20000Hz |
|
Noise
Level |
|
|
|
Machine without vacuum
aggregate |
max.78 dB(A) |
max.78 dB(A) |
|
Vacuum
Option |
|
|
|
- 29kVA aggregate |
max. 82 dB(A) |
max. 82 dB(A) |
|
- 58kVA aggregate |
max.87 dB(A) |
max.87 dB(A) |
|
Machine
Dimensions |
|
|
|
Cutting area |
per spec.. |
per spec.. |
|
X-axis stroke |
3000mm |
per spec.. |
|
Y-axis stroke |
1800mm |
approx.1800mm |
|
Z-axis stroke |
80mm |
80mm |
|
C-axis stroke |
n*360 deg. |
n*360 deg. |
|
Cutting Speeds |
|
|
|
Maximum Cutting speed (X,Y) |
0-45m/min |
0-60m/min |
Acceleration/deceleration (X,Y)
Rapid move
/
Cutting |
2.5m/s²
/
1.5m/s² |
2.5m/s²
/
2.5m/s² |
|
Acceleration/deceleration (Z) |
max. 10m/s2 |
max. 10m/s2 |
|
Acceleration/deceleration (C) |
900 rad/s2 |
900 rad/s2 |
|
Dynamic Acceleration
Factor |
|
|
|
Machine
Accuracy |
|
|
|
Positioning accuracy in
X + Y |
±0.5mm |
±0.4mm |
|
Positioning accuracy in
X+Y (w. Axis calibration) |
±0.2mm |
±0.2mm |
|
Repeatability in X + Y |
±0.25mm |
±0.2mm |
|
Repeatability in X +
Y (with Axis calibration) |
±0.1mm |
±0.1mm |
|
Profiling Accuracy (in
Mylar) |
±0.8mm |
±0.8mm |
|
Profiling Accuracy (with Axis calibration) |
±0.4mm |
±0.4mm |
|
Drive
System |
|
|
|
Motors |
AC-Servo |
AC-Servo |
|
Control
System |
|
|
|
Type |
GFM CNC6000 |
GFM CNC6000 |
